Atmel Wireless LAN Access Point Guida Utente Pagina 1

Instant WirelessTMSeries Wireless NetworkAccess PointUse this guide to install: WAP11User Guide

Instant WirelessTMSeriesConfiguring the WirelessNetwork Access PointThe Wireless Network Access Point can be configured one of two ways,through the US

5.The Choose Destination Location screen will show you the default desti-nation chosen by the utility. It is recommended that you leave the default de

• WEP. If you have not enabled WEP encryption, this will read Disabled. Itwill read Enabled when WEP encryption is in use.• Reconnect. If, for any rea

2120THE ADVANCED TABBefore making any changes to the Advanced tab, please check your wirelesssettings on other systems, as these changes will alter th

• Operational Modeby default is set toAccess Point. This isfor connecting yourwireless PCs to awired network. Inmost cases, no changeis necessary to

THE SECURITY TABWEP (Wired Equivalent Privacy) is a data privacy mechanism based on a 40 bitshared key algorithm, as described in the IEEE 802.11b sta

27• WEP Key Setting. This setting will be the configuration key used inaccessing the wireless network via WEP encryption. To generate an encryp-tion k

To restore your temporary IP address configuration, follow the steps below:1. Follow steps 1 and 2 in the instructions above.2. Select either Specify

30• Channel. The wireless channel shared by all wireless devices connected tothis Access Point.• WEP. If you have not enabled the WEP encryption proto

THE ADVANCED TABBefore making any changes to the Advanced tab, please check your wirelesssettings as these changes will alter the effectiveness of the

COPYRIGHT & TRADEMARKS Copyright © 2001 Linksys, All Rights Reserved. Instant Wireless™ is a registered trade-mark of Linksys. Microsoft, Window

• Basic Rates. The basic transfer rates should be set depending on the speedof your wireless network. Older, slower wireless networks should be set at

• WEP Key Setting. This setting will be the configuration key used inaccessing the wireless network via WEP encryption. To generate an encryp-tion key

To enable MAC Address Filtering follow these steps:1. Create a text file (e.g. MAC.TXT) using Notepad or another text editor.2. Enter the 10 digit M

What IEEE 802.11 features are supported?The product supports the following IEEE 802.11 functions: • CSMA/CA plus Acknowledge protocol • Multi-Channel

What is DSSS? What is FHSS? And what are their differences?Frequency-hopping spread-spectrum (FHSS) uses a narrowband carrier thatchanges frequency in

44DSSS - Also known as “Direct Sequence Spred Spectrum”, this is a variety ofradio transmission methods that continuously change frequencies or signal

46RJ-45 - A connector similar to a telephone connector that holds up to eightwires, used for connecting Ethernet devices.Roaming - The ability to use

SpecificationsStandards: IEEE 802.3 (10BaseT), IEEE 802.11b (Wireless) Channels: 11 Channels (US, Canada)13 Channels (Europe)14 Channels (Japan)Ports

51Warranty InformationBE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODEFROM THE PRODUCT'S PACKAGING ON HAND WHEN CALLING.RETURN REQUESTS CANNO

Contact InformationFor help with the installation or operation of this product, contact LinksysCustomer Support at one of the phone numbers or Interne

Wireless Network Access PointIntroductionThe Instant WirelessTMWireless Network Access PointDon’t be bound by cabling restrictions any longer! The Ins

© Copyright 2001 Linksys,All Rights Reserved.http://www.linksys.com

Wireless Network Access Point3Planning Your Wireless NetworkNetwork TopologyA wireless LAN is a group of computers, each equipped with one InstantWire

Instant WirelessTMSeriesGetting to Know the WirelessNetwork Access PointThe ADSL Modem Router’s Rear PanelYour Access Point’s ports, where network cab

Instant WirelessTMSeriesConnecting and Setting Up theWireless Network Access Point 1. Locate an optimum location for the Wireless Network Access Point

3. Windows will now ask you where to search for the driver software. SelectSpecify a location and type in the blank field D:\WAP11\WIN9X (where“D” spe

1. Windows 2000 will automatically identify the Wireless Network AccessPoint, once it is connected to the PC, and prompt you to install the necessaryd

5. Windows will now install the driver files. Click the Finish button when com-pleted.6. Continue on to the Configuring the Wireless Network Access Po